Water heatersHome maintenanceHard waterWhen to call a plumber

Are You Shortening Your Water Heater's Life?

We write for the TL;DR crowd

This article was written to be skim-friendly.

If you only read the headings and bold lines, you’ll still walk away knowing what most homeowners don’t: your water heater needs yearly maintenance, and skipping it costs more later.

So read all of it, read half of it, or skim the bold parts. If you leave knowing when to flush your water heater, this article did its job.

Your water heater works harder than almost anything else in your home

Think about how many times a day you use hot water. Morning showers. Dishes after dinner. A load of laundry. Washing your hands. Every one of those runs through your water heater, every single day, all year long.

Yet most people never think about it. Water heaters are usually tucked away out of sight in a garage, basement, crawlspace, attic, utility closet or laundry room.[1] Out of sight means out of mind, right up until the morning the shower runs cold.

Key point: Your water heater is one of the most-used appliances in your home and one of the most expensive to replace. Water heater manufacturer A. O. Smith puts it plainly: buying a new water heater or replacing your current one can be expensive, and routine maintenance helps you get the most out of the one you have.[2]

But every day it runs, it’s slowly filling up with sediment

Your tap water carries dissolved minerals. Over time, some of those minerals separate and settle at the bottom of the tank as sediment.[3] It happens a little at a time, every day, whether you notice it or not.

The harder your water, the faster it builds up. Hard water has a higher concentration of minerals, which increases the risk of sediment building up inside the tank.[2] Left alone, that sediment raises the risk of leaks and bad smells, cuts your water heater’s efficiency, and can even clog your water lines.[2]

Your tank also has a part designed to wear out slowly. Steel water heaters have an anode rod, a metal rod made of aluminum, magnesium or zinc that hangs down into the tank. It attracts the minerals and salts in your water so they eat away at the rod instead of the tank.[2] Once the rod is used up, the tank itself is next. How long the rod lasts depends on your water, how much hot water you use and whether you have a water softener, which is why A. O. Smith recommends inspecting it once a year.[2]

That buildup is what cuts its life short

Sediment acts like insulation at the bottom of the tank. Your water heater has to run longer heating cycles, which uses more energy and puts more stress on its heating parts.[3]

More strain, every day, adds up to a shorter life. The International Association of Certified Home Inspectors (InterNACHI) estimates that a conventional water heater lasts about 6 to 12 years, and notes that the mineral content of your water can shorten that.[4] Energy Trust of Oregon puts the range wider, from 8 to 20 years.[1]

That’s a big gap. Water quality and how well a heater is cared for both affect where yours lands, and according to Rheem, flushing is one of the most effective ways to extend a water heater’s lifespan.[3]

Key point: An unmaintained water heater doesn’t just cost more to run. It can force you to buy a new one years earlier than you needed to.

The good news: it’ll warn you before it fails

Sediment problems rarely show up overnight. Your water heater usually gives you early warning signs. Here’s what to watch for:

  • Rumbling or popping noises. This is the classic sediment sound, and it’s often something a flush can fix.[3]
  • Rusty, cloudy or tinted hot water. Discolored hot water can point to sediment or corrosion inside the tank.[1][3]
  • Hot water running out faster than it used to. If showers are getting shorter or the water temperature drops, sediment may be taking up room or blocking heat.[1][3]
  • Longer waits for hot water to come back. Slow recovery between uses is another sign the heater is working harder than it should.[3]
  • Higher energy bills with no change in use. When your heater runs longer to do the same job, your bill shows it.[3]
  • A leaking tank. Energy Trust of Oregon lists a leaking tank as a sign it may be time for a new water heater.[1]

Age matters too. Energy Trust of Oregon suggests that a tank-style water heater 8 to 10 years old may be due for an upgrade.[1] Not sure how old yours is? Check the label on the side of the tank. The date is usually built into the serial number, and each brand writes it a little differently.[1]

Key point: Noises, discolored water and shorter showers mean it’s time for a flush. A leak or an older tank means it’s time to call a plumber.

A once-a-year flush stops the damage before it starts

For most homes, flush your water heater once a year. If you have hard water, flush it every six months. That’s Rheem’s recommendation,[3] and A. O. Smith says most tank water heaters need flushing at least once a year, and more often in hard-water areas.[2] For your specific model, A. O. Smith says to follow the instructions in your manufacturer’s handbook.[2]

What a flush actually is: the tank drains through the drain valve at the bottom, then cold water runs through until no more sediment flows out and the water runs clear.[2][5] The whole process usually takes a few hours, and longer if the tank is left to cool down first.[5]

A professional flush covers more than just the flush. According to Rheem, a technician typically also inspects the temperature and pressure (T&P) valve, checks that the drain valve works, evaluates the anode rod, tests system pressure, checks for leaks and confirms the heater runs properly afterward.[3]

Have a tankless water heater? It still needs maintenance. Tankless units don’t have a tank to flush, but minerals still build up inside and need descaling.[2][3] Rinnai, a major tankless manufacturer, recommends flushing those mineral deposits at least once a year. Its process uses about 4 gallons of undiluted white vinegar and can take up to 45 minutes.[6]

Never flushed yours? Let a plumber handle the first one

Flushing a water heater can be a do-it-yourself job, but not always. A tank that hasn’t been flushed in years is different.

Years of sediment can harden, clog the drain valve and turn a simple flush into a leak. Rheem notes that older tanks, or ones that haven’t been flushed in a while, may have hardened sediment that’s hard to remove without specialized tools, and that trying to flush them yourself could lead to leaks or further damage.[3] A. O. Smith also warns that sediment can clog the drain valve, and says to call a plumber if you can’t flush the tank.[2]

Call a plumber instead of doing it yourself if:

  • The drain valve won’t open or is leaking[3]
  • You see heavy rust or corrosion around the fittings[3]
  • The noise keeps going even after a flush[3]
  • Your water heater is 8 to 12 years old or older[3]
  • You’re not comfortable working around gas or electrical parts[2][3]

Energy Trust of Oregon gives similar advice: if your water heater is more than 10 years old, draining and flushing it could expose other, more serious problems.[5]

After a professional flush, it’s easier to stay on top of it. A. O. Smith recommends that homeowners test the temperature and pressure relief valve once a year and have a professional inspect it every 5 years.[2] Watching for leaks and the warning signs above goes a long way between visits.

Key point: If your water heater has never been flushed, the first one is the riskiest. Let a plumber do it, then keep it on a yearly schedule.

Service it like your car, and it’ll last like one

You change your car’s oil on a schedule because you drive it every day. Skip it long enough, and you’re not paying for an oil change anymore. You’re paying for an engine.

Your water heater works the same way. It runs every day, wears down a little every day, and a little yearly maintenance keeps it from failing early.

Your yearly water heater checklist, based on A. O. Smith’s annual maintenance recommendations:[2]

  • Flush the tank to clear out sediment
  • Test the temperature and pressure relief valve
  • Inspect the anode rod and replace it if it’s worn down
  • Check for leaks around the tank and connections
  • Check the thermostat, which is typically set no higher than 120°F

The bottom line: a yearly flush costs far less than a new water heater and keeps yours running longer.

Not sure when your water heater was last serviced? That’s the sign it’s time. Bright Plumbing is a family-owned plumber based in Auburn, WA. Book annual water heater maintenance online or call us at 206-307-4216. If your water heater needs to be replaced, we can help with that too.

Sources

  1. Energy Trust of Oregon: How old is my water heater?. https://www.energytrust.org/residential/tips/how-old-is-my-water-heater/
  2. A. O. Smith: Water heater maintenance guide. https://www.hotwater.com/info-center/water-heater-maintenance.html
  3. Rheem: How often to flush your water heater (and how to do it). https://www.rheem.com/water-heating/articles/how-often-to-flush-your-water-heater-and-how-to-do-it/
  4. InterNACHI: Standard estimated life expectancy chart for homes. https://www.nachi.org/life-expectancy.htm
  5. Energy Trust of Oregon: Drain, flush and save: water heater maintenance 101. https://www.energytrust.org/residential/tips/drain-flush-and-save-water-heater-maintenance-101/
  6. Rinnai: 13-step tankless water heater flushing procedure. https://www.rinnai.us/residential/flushing-my-rinnai-tankless-water-heater

← Back to the blog

Need a plumber?

Book online and pick a time that suits you, or call and talk it through with us.

Call Now: 206-307-4216